Designation: D − 10Standard Test Method for Energy Measurement for This test method is under the jurisdiction of ASTM Committee D18 on Soil and. Purchase your copy of ASTM D – 16 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards available. ASTM D ,. “Standard. Test Method for Stress Wave. Energy Measurement for Dynamic. Penetrometer. Testing. Systems”. [2], speclfles.

Author: Jujind Shakasida
Country: Turks & Caicos Islands
Language: English (Spanish)
Genre: Life
Published (Last): 12 March 2011
Pages: 329
PDF File Size: 19.59 Mb
ePub File Size: 13.75 Mb
ISBN: 317-5-39434-531-4
Downloads: 54039
Price: Free* [*Free Regsitration Required]
Uploader: Akikazahn

Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method. Valid Buy asstm standard. Soil and Rock I: Sustainable Development Goals and standardisation, how do they connect? It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design. The N-value depends on the soil properties but also on the mass, geometry, stroke, anvil, and operating efficiency of the hammer.

These notes and footnotes excluding those in tables and figures shall not be considered as requirements of the standard. Subscribe on standards – Read more. Report error on page. The inch-pound units given in parentheses are mathematical conversions which are provided for information r4633 only and are not considered standard.

It is not intended for use with down-hole hammers. This v4633 may also be applicable to other dynamic penetrometer tests.

This procedure may also be applicable to other dynamic penetrometer tests. Asym is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Shopping cart Close cart 0, foreach: Read more about SIS Subscriptions. Engineering properties can be estimated on the basis of empirical correlations between N-values and soil density, strength or stiffness.

  ANTHONY KALDELLIS PDF

The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Please note that the selected standard is invalid. This energy measurement procedure can evaluate variations of N-value resulting from differences in the hammer system.

Subscribe on standards with our subscription service. When you use our service you can be assured the latest editions and easy access. See also Refs 1- 6. Since the measured energy includes the extra potential energy effect due to the set per d633, tests for energy evaluation of the hammer systems should be limited to moderate N-value ranges between 10 and 50 Ref 7.

ASTM D – 16 – Standard Test Method for Energy Measurement for Dynamic Penetrometers

The inch-pound units given in parentheses are mathematical conversions which are provided for information purposes only and are not considered standard. The Standard Penetration Test is the most common type. In addition, they are representative of the significant digits that generally should be retained. Reliable results depend on many factors: What is a standard?

ASTM D4633 – 16

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Practice D provides a means of evaluating some axtm those factors.

  MACAM MACAM TERAPI KOMPLEMENTER PDF

Link to Active This link will always route to the current Active version of the standard.

Contact us svenska Login. The standard is adtm in your shopping cart. Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method.

It is not intended for use with down-hole hammers. In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs. Message to your colleague.

General terms and conditions Cookies och Javascript Disclaimer Contact. Alternatively, the N-value can be used directly in foundation design using correlations to design parameters such as allowable bearing pressure or pile capacity. In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs. Historical Version s – view previous versions of standard.

The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it aastm common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. Your shopping cart is empty.

Users of this standard are cautioned that compliance with Practice D does not in itself assure reliable results.