All OMRON products are capitalized in this manual. The word .. purpose and a comparison between the CQM1H and the CQM1. Section 2. 1. V4+. Voltage pin, input 4. 2. V Common pin, input 4. 3. V3+. Voltage pin, input 3. 4. V Common pin, input 3. 5. V2+. Voltage pin, input 2. 6. V Common . View and Download Omron CQM1 operation manual online. Programmable Controllers. CQM1 Controller pdf manual download. Also for: Sysmac cqm1.

Author: Arashisho JoJozshura
Country: Austria
Language: English (Spanish)
Genre: History
Published (Last): 13 November 2011
Pages: 391
PDF File Size: 16.27 Mb
ePub File Size: 14.32 Mb
ISBN: 259-8-76771-877-3
Downloads: 10794
Price: Free* [*Free Regsitration Required]
Uploader: Kazikasa

Additions and changes made to application precautions.

OMRON CQM1 OPERATION MANUAL Pdf Download.

Page Glossary nonfatal error A hardware or software error that produces a warning but does not stop the PC from operating. Con- nect a to VDC power supply. Decimal Monitor Without Sign 3-word data modification can be used during execution. Monitoring The input word has flags for comparison results, overrange detection, manuaal sensor disconnection detection as shown below.

Terminal Arrangement Power supply cable Bit Number Allocation Word Allocation Output words are allocated according to the mounting order from left to right of the Units. IOTC — — Mxnual The actual data reading timing must be later than the moment timing input to the Unit is ON.

Page 70 28 Slaves G Remote Terminals. Press the Up Arrow Key to delete the specified instruction. Troubleshooting Flowcharts Section Cqk1 Error Check The following flowchart can be used manul troubleshoot fatal errors that occur while the Power indicator is lit. LSS Capabilities Section 2. The total current consumption of the components in a PC must be less than the capacity of the Power Supply Unit being used.

Output data is hexadecimal. If a set point was previously C, it will be changed to The command code is set to the output word. The width varies with the Power Sup- ply Unit, as indicated.

  BURN THIS LANFORD WILSON PDF

Page 43 Section Wiring 4. Scaling Therefore, if the Unit is operated with the factory-set scaling values with an input range from 4 to 20 mA, an input of 4 mA will be regarded as and an input of 20 mA will be regarded as Page Glossary cwm1 designator An operand that is used to designate the bit or bits of a word to cq1 used by an instruction.

C Setting Example In manul example, the timing hold is set to normal, and the L or H set value is adjusted using the teach function. Indicator Alarm Table The table below shows the description and remedy of an error occurring in the G Interface Unit. The Slave address for Unit 2 can only be used for an 8-point or point Slave. Not lit when set to 16IN.

Page Troubleshooting Flowcharts Section Fatal Error Check The following flowchart can be used to troubleshoot fatal errors that occur while the Power indicator is lit.

Due to the small terminals, be careful not to short the wires when wiring. Mounting And Wiring Connect each input line to the terminal using a solderless terminal. See add count input. Addresses 24 to 27 cannot be set for 4-point Slaves.

Handle the opti- cal fiber cables with care because they are thin. Verify C-series PCs only Monitor Input the set value teach command code C for the L value.

Page Programming and Adjustment 3. Dip Switch Standard communications parameters see note 2 will be set for the following serial communications ports. Section Wiring 4. Scaling Example for Measuring Lengths Using a Sensor with an Input of 4 to 20 mA If the output of the sensor is 4 mA when the length of the object sensed by the sensor is 10 centimeters and the output of the sensor is 15 mA when the length of the object is 30 centimeters, the following data should be input.

  EL DERECHO PRIVADO ROMANO GUILLERMO FLORIS MARGADANT PDF

Note The positive and negative terminals of the transmission terminals 1 and 2 are shorted internally. Multiple-application controllers with a wide range of functions 70 pages. Weight 26 g Note 1. Terminology and Function Descriptions The command codes can be set to output word.

Smartslice grt1-series, ethercat communication unit pages. These two ports can be used to carry out absolute-type high-speed counter interrupts. If the correct command code or parameter is set to the output word, the same command code or parameter will be set to the input word. manusl

Programming Console Operation The command codes can be set to output word. Revision History A manual revision code appears as a suffix to the catalog number on the front cover of the manual. Connection of a Variety of Sensors ON mznual the alarm is set to Not lit when set to 2 words 32 points.

OMRON CQM1 Operation Manual

LSS Capabilities Section Mode Setting Note The sensitivity of the E3X-MA11 is set to maximum if teaching is performed with very little light or if the sensor head is not located within the sensing dis- tance. At the connec- tor on the CQM1 side, wrap aluminum tape around the twisted wire as shown in the illustration, and secure the wire to the hood.

The data can be altered with this function. Note The sensitivity of the E3X-MA11 is set to maximum if teaching is performed with very little light or if the sensor head is not located within the sensing dis- tance.