MC Three-terminal Positive Voltage Regulator These voltage regulators are monolithic integrated circuits designed as fixedvoltage regulators for a wide. MC Fairchild datasheet pdf data sheet FREE Datasheets (data sheet) search for integrated circuits (ic), semiconductors and other electronic components. Motorola Semiconductor MC datasheet, (MC Series) Three Terminal Positive Fixed Voltage Regulators (1-page), MC datasheet, MC pdf.
|Published (Last):||22 April 2008|
|PDF File Size:||10.14 Mb|
|ePub File Size:||8.13 Mb|
|Price:||Free* [*Free Regsitration Required]|
Long Term Stability – Output voltage stability under accelerated life test conditions with the maximum rated voltage listed in the devices’ electrical characteristics and maximum power dissipation. That means that when your load consumes 10W the switcher will only dissipate 1W. Output Noise Voltage – The rms ac voltage mc7821 the output, with constant load and no input ripple, measured over a specified frequency range.
MC7812 Datasheet PDF
So if you have a 12W load it will draw 1A from the regulator. Load and line regulation are specified at constant junction temperature. A control element will vary the resistance in practice a transistor so that the output voltage will remain constant regardless of input voltage and load.
Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Functional operation above the Recommended Operating Conditions is not implied.
Post as a guest Name. In order to minimize dissipation the MCC is chosen in this application. Even though the typical dropout voltage is 2 volts, you should use the maximum value in your design.
This is a snapshot of datashwet For example, a 1. Normally good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead.
Stresses exceeding Maximum Ratings may damage the device. The is a non-LDO linear regulator, which means it needs a higher input voltage.
MC Datasheet(PDF) – Fairchild Semiconductor
The measurement is made datxsheet conditions of low datashewt or by using pulse techniques such that the average chip temperature is not significantly affected. Load Regulation – The change in output voltage for a change in load current at constant chip temperature. Resistor R determines the current as follows: Output Current in Excess of 1. Internal Short Circuit Current Limiting? Dztasheet Mortensen 1, 3 14 Since the output is 12 volts, you add the two together to get a minimum input of But since there’s this voltage drop the input voltage has to be higher than the output voltage.
Sign up or log in Sign up using Google. They are like a variable series resistor between input and output, causing a voltage drop across the regulator.
The input voltage must be above the output. How does it go from a Maximum dropout voltage to a minimum input voltage? The current sensing PNP must be able to handle the short circuit current of the three-terminal regulator. Although designed primarily as a fixed voltage regulator, these devices can be used with external components to obtain adjustable voltages and currents. From what datahseet understand then from your answer The difference of 8W will be dissipated in the regulator.
XX, These satasheet digits of the type number indicate nominal voltage.
Datasheet – MC – Voltage Regulators – Motorola
SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur.
Therefore, a four-ampere plastic power transistor is specified. Linear regulators are different. An LDO might have a dropout voltage of 0.
A note on dissipation: On page 6 of the datasheet, the maximum dropout voltage Vd is listed as 2. In many low current applications, compensation capacitors are not required.
Dean 4, 22 57 Resistor R in conjunction with the VBE of the PNP determines when the pass transistor begins conducting; this circuit is not short circuit proof. However, it is recommended that the regulator input be bypassed with a capacitor if the regulator is connected to the power supply filter with long wire lengths, or if the output load capacitance is large.