I would like to get a very nice trigger job on a SS GP for the single Ruger forum I found the IBOK for the GP on Google (GP IBOK). I received the GP pdf this morning. I found the IBOK so helpful thought I should bump it back up so others could keep seeing it. Gp Ibok – PDF Free. Download – -. Ruger sp manual pdf ruger sp manual pdf magnum revolver like the. Ruger GP For many.

Author: Tojazshura Vitilar
Country: Czech Republic
Language: English (Spanish)
Genre: Love
Published (Last): 19 June 2015
Pages: 410
PDF File Size: 18.60 Mb
ePub File Size: 16.55 Mb
ISBN: 196-8-29606-241-9
Downloads: 24715
Price: Free* [*Free Regsitration Required]
Uploader: Zuluzragore

It had very rough machining in several places as well as some metal burrs that made it a pain in the rear to take apart. Usually I just shoot out in the desert near my home so I make up my own targets as I go.

Buff the top of the latch the rounded part that locks into the cylinder until it looks ibol chrome. As for ammo, they’re bore sighted with gr at the factory, so that tends to be the best shooter. Locate the plunger tip and push it forward with a screwdriver or other tool while pulling downward lightly on the trigger guard. I have a Ruger security six magnum stainless and an SP iboo stainless that I just completed using the information in your article.

While pressing the plunger down, push the latch pivot pin part 25 ibo from the inside of the crane. A fine file will work well to remove burrs or high spots. Use a file or Dremmel Tool to round all four edges of the strut.


Apply a drop of oil on the hammer pivot pin then insert it into the frame.

Lift the sight off. It is easiest to install by placing the arrowhead end in first iboj holding the back up at an angle.

Strange problem with my GP100

The guns felt like they had trigger jobs done on them. The stronger the spring, the heavier both SA and DA trigger pull will be. Place your left index finger in the trigger guard behind the trigger. Do the same test in DA by pulling the trigger and watching the cylinder latch. Dress as necessary to remove sharp edges, rough spots, or residue.

December 4th, The assembly is held in the frame by a spring-loaded plunger part Get that unit apart and give it a good visual.

New GP – Survivalist Forum

It’s a million-times easier to polish one of those than a bead-blasted finish on a semi-auto. I carry it from time to time, To kbok it looks very nicely finished and the bluing is very deep. I am a mechanical engineer and believe me, the parts fit, tolerances, and surface finish could be improved in their automated processes to nearly duplicate what Iowegan and other gunsmiths have been doing to these guns for years.

He was suggesting that you disassemble the gun iboo clean the inside. Yes, there is a huge comfort factor difference between the hammer and the grip. Iowegans books are sold out until Fall, though.


GP100 IBOK for SP101

Sun Dec 02, 3: I’ve also smoothed the hammer checkering, and polished the internals per Iowegan’s instructions. I would carefully check the transfer bar and the track it runs in for any obstructions or possible burs, if found they may be smoothed down with an emery board or a small piece of sandpaper.

Funny thing is I seem to shoot better double action than I do single action. I would never hesitate to use it as a field gun on hunting trips or for home defense. Add shipping to cost consideration. Send a private message to Apocalypse Now.

Strange problem with my GP

Find all posts by Apocalypse Now. Remove the latch plunger part 30 and the spring part 8 from the trigger guard assembly. Grab the strut assembly and pull it out of the gun. Would you like to see better stuff offered in the contest?

Iowegan, Thanks for the copy you sent me the other day,it’s real helpful. Next on the shopping list is a holster, possibly a brighter front sight and I’d like to put sharp looking wood grip on it. Am I stuck with a two-piece style grip? Insert the case in a chamber and locate it directly in ibkk with the firing pin hole.